information about bios and system: system ID: 68 country code: 1 system BIOS revision: 1.09 system management BIOS revision: 1.05 SMAPI BIOS interface revision: 0.92 video BIOS revision: 1.15 slave controller revision: 1.5 info from cmos RAM: CMOS RAM has power?: Y CMOS RAM has lost power?: N CMOS RAM has bad checksum?: N CMOS RAM has bad equipment info?: N CMOS RAM has bad mem size info?: N CMOS RAM has bad time info?: N hard disk failed initialization?: N shutdown status: 0x0 display operating mode: 0x0 (reserved code) coprocessor present?: Y diskette drive type: 4 (i.e., 1.44 MB) number of diskette drives: 1 diskette drive 0 present?: Y hard disk drive 0 type: 0xf hard disk drive 1 type: 0x0 (i.e., not present) hard disk drive 2 type: 0x0 (i.e., not present) hard disk drive 3 type: 0x0 (i.e., not present) conventional memory below 640KB: 640 KB expansion memory above 1MB: 65535 KB usable contiguous memory: 65535 KB information about display: panel type: 3 (i.e, color TFT LCD) panel dimension: 2 (i.e., 1024 x 768) monitor type: 0 (i.e., no CRT attached) monitor has DDC1 capability?: N monitor has DDC2 capability?: N information about docking station: docking station ID: (not docked) security key unlocked?: - bus connected?: - information about processor: CPU manufacturer: Intel microprocessor type: 6 microprocessor stepping level: 106 CPU clock: 66 MHz internal clock: 300 MHz is: the lid closed?: N the keyboard open?: N the AC adapter attached?: Y information about UltraBay II: device type: 0x10 (i.e., IDE) device ID: 0x10 (i.e., CD-ROM) setup of display: CMOS current internal display enabled?: enable enable crt display: enable disable tv display: disable disable 2ual display: enable enable TV display selected?: N N monitor detection ignored?: N N setup of fn hotkey: sticky Fn key supported?: N sticky & locked Fn key supported?: Y fn hotkey state: nonsticky setup of pointing device: CMOS current internal pointing device controllable state?: Y Y auto control supported?: Y Y activation mode: auto-disable auto-disable external pointing device controllable state?: N N activation mode: disable disable setup of: CMOS daylight saving time: disable power management modes: ac power expenditure: high battery power expenditure: auto RediSafe global mode overrides non-global mode?: Y RediSafe globally enabled?: N power management resume events: capability current appointment-r.t.clock-initiated?: Y N (centennially 255-255-255 255:255:255) hardware-initiated?: Y Y lid-opening-initiated?: Y Y serial-RI-initiated?: Y Y power management sedative events: capability current (SZRHO) (SZRHO) hardware-or-software-initiated: SZ-HO SZ-HO power-switch-initiated: ---HO ----O lid-closure-initiated: -Z--- -Z--- Standby-timer-initiated: S---- S---- Zuspend-or-hibern.-timer-initiated: -Z-H- -Z--- Hibernate-from-susp.-timer-init'd: ---H- ---H- battery-low-initiated: -Z-H- -Z--- env'mt-exhausted-initiated: -Z--- -Z--- power management timer modes: capability current Standby timer: N N Zuspend-or-hibernation timer: Y Y Blank-internal-display timer: Y Y drive power-down timer: Y Y power management delay of Hibernate-from-suspend: 0 (i.e., disabled) power management delays of Zuspend or hibernate: current (specifiable in each power mode)? ac power "manual" expenditure mode: Y 0 (i.e., disabled) battery "manual" expenditure mode: Y 5 minutes "high" power expenditure mode: Y 0 (i.e., disabled) "auto" power expenditure mode: Y 5 minutes resource state: ioaddr irq# able? mode/power floppy controller: 0x3f0 IRQ6 enable parallel port: 0x3bc IRQ7 enable ext serial port 1: 0x0 IRQ0 disable (error) serial port 2: 0x3f8 IRQ4 enable